螺钉装配机自动上料装置的设计(含CAD零件图装配图)

螺钉装配机自动上料装置的设计(含CAD零件图装配图)(任务书,开题报告,外文翻译,论文说明书8800字,CAD图纸5张)
摘  要
本文介绍了国内外螺杆机组装，原则和发展状况的基本概念。组合式螺丝组装机螺丝和垫圈用于在一台机器安装。可用配备紧固件供给装置和收集装置的市场模块化螺钉装配机上的装置，用于进给螺钉和垫圈到连接装置，螺钉，并传递到包装组件，组装之后，并输送到收集装置内。螺钉和垫圈在组装过程中，以确保该螺钉和垫圈可以一起运到安装基座组件中，如果在运输途中的错误，只留下螺钉或垫圈装置，组件并不意味着组装半成品在收集装置输送到收集装置做许多良好的中间产物未安装，严重地影响了产品的质量，没有中间产物被筛选的跑步机上将会丢失设备非常敏感或错误地装载情况发生时，它是很难保证产品的质量，并验证了良好的螺丝和垫圈安装后，现有的组装机安全不好，你需要手动，费时费力，工作效率不高，所以产品的成品率不高。然后专门针对配置组装机的螺杆组成和传输。对于汽缸部进行了非常详细的计算和验证。

关键词：螺钉装配机,气缸，自动上料装置

The Design of Screw Assembly Machine Automatic Feeding Device
Abstract
This paper introduces the basic concepts of screw machine assembly, principles, and development situation at home and abroad. Combined screw assembly machine screws and washers are used to assemble in one machine. Available on the market modular screw assembly machine comprising feeding means mounting means and collecting means, means for feeding screws and washers supplied to the mounting means, screws and gasket assembly, after assembly, and transported to the collection device Inside. Screws and washers in the assembly process, must ensure that the screws and washers can be transported together to the mounting device assembly, if a mistake during transportation, resulting in only the mounting screws or gasket means, the assembly also means would not assembled semi-finished products delivered to the collection device in the collecting device means a lot of good semi-finished products is not installed, has seriously affected the quality of the product, no semi-finished products were screened on the assembly machine will be very prone to missing equipment or mistakenly loaded situation occurs, it is difficult to ensure the quality of the product, and the existing assembly machines installed securely bad after a good screw and washer, you need to check the manual defective, time-consuming, work efficiency is not high, so product yield is not high. Then specifically addressed the assembly machine screw composition and transmission configuration. Focusing on the cylinder section carried out a detailed calculation and verification.

Key words: screw assembly machines, cylinder, automatic feeding device
 
原始数据： 料斗外径 =208mm、中径 = 190mm和高度h=60mm 螺旋料槽螺距t=42mm螺旋槽宽度 =12mm 弹簧倾角 =20° 设计螺钉装配机自动上料装置。
 

目 录
摘  要    2
Abstract    3
第1章 绪论    1
1.1 课题背景    1
1.2  课题的研究意义    1
1.3 螺钉及螺钉装配机概况    2
第2章 螺钉装配机的总体设计    3
2.1 螺钉装配机的原理    3
2.2 系统工作原理图    3
2.3自动供料排序机构振动盘的设计    4
2.3.1供料机构的任务基本组成及设计要求    4
2.3.2 振动盘的介绍    5
第3章 主要执行机构(气缸)选型    7
3.1气缸的设计计算    7
3.2 气缸的流量计算    7
3.3 气压马达的设计计算    8
3.4 气压元件的选择    8
3.5 气缸的选型    9
3.6 推料气缸型号确定    11
3.7 导向装置    12
3.8 平衡装置    12
3.9 合金的使用    13
总结与展望    14
参考文献    15
致 谢    16